Moisture Mitigation System 950G

TERRAZZCO's green system for epoxy terrazzo. Moisture Mitigation System 950G is designed to prevent the transmission of moisture vapors from concrete slab to the terrazzo surface.

TERRAZZCO Moisture Mitigation System 950G

Moisture Mitigation 950G is a VOC free two-component epoxy resin based on renewable ingredients. It does not contain any ingredients on The Living Building Challenge (LBC) Red List. When applied on the top surface of concrete slabs, the coating provides a retarder against moisture vapor transmission for slabs possessing relative humidity measurement greater than 75% (see application section below for applicable test method). MMS 950G yields approximately 300-400 square feet per mixed unit. This yield comprises one coat but is based on porosity of the concrete and may require a second coat for very porous surfaces.

Download Product Data

Quick & Easy

Easy application for tight construction schedules

No Red List

Renewable ingredients that are Red List free

VOC Free

Sustainable impact with improved indoor air quality

Moisture Resistant

Protects terrazzo surfaces for years to come

Typical Uses of MMS 950G

Moisture Mitigation System 950G is used to mitigate moisture vapor transmission through concrete slabs having greater than 75% relative humidity when tested according to ASTM F2170.

Advantages of Moisture Mitigation System 950G

Renewable ingredients
Free from LBC Red List ingredients
VOC free for a healthier environment
Eco-friendly contributing to LEED® credits
Easy application for tight construction schedules
Packaged and premeasured for easy mixing at worksites
Manufactured and supplied from Southeast United States

Application & Technical Data

Working Data

Working (Pot) Life: 30 minutes

Re-Coat Time: 5-6 hours @ 75°F

Full Cure Time: 7 days

Mix Ratio

Pour TERRAZZCO Moisture Mitigation System MMS 950G Part A resin (3.5 gallons premeasured) with Part B hardener (1 gallon premeasured).

Coverage

MMS 950G yields approximately 300-400 square feet per mixed unit. This yield comprises one coat but is based on the porosity of the concrete and may require a second coat for very porous surfaces.

Mixing Instructions

1. Pour the pre-measured MMS 950G hardener part B into premeasured MMS 950G part A and mix thoroughly for two to three minutes using a drill equipped with a jiffy blade.

2. Add 1.25 L (0.33 gal) water and mix for two minutes.

3. Add another 1.25 L (0.33 gal) water and mix for two minutes.

4. Add another 1.25 L (0.33 gal) water and mix for two minutes.

5. Finish adding another 1.25 L (0.33 gal) water and mix for two minutes.

6. Once the mixture has been thoroughly mixed, the product may be applied by roller, squeegee, or brush. Apply evenly with no puddles, making sure of uniform coverage. Coverage will vary depending upon the porosity of the substrate. Multiple coats may be necessary for very porous surfaces. Allow curing for 5-6 hours.

Documentation & Product Details

Documents

Document	Download
3-Part Guide Specification for Thin-Set Epoxy Terrazzo #096623 (PDF)
3-Part Guide Specification for Thin-Set Epoxy Terrazzo #096623 (MS Word Doc)
Product Data – Moisture Mitigation System MMS 950G
TERRAZZCO Architectural Binder
Care and Maintenance Guide
Sustainability Guide
NTMA Systems Guide
Products and Service Brochure
Samples Brochure

Packaging Details

TERRAZZCO Moisture Mitigation System 950

Packaging

TERRAZZCO® MMS 950G is packaged for convenient mixing at the worksite. Part A resin is premeasured in 3.5-gallon pail. Part B hardener is premeasured in a 1-gallon can.

Self Life: Material has a one-year shelf life from the date of manufacture when stored at 55°F to 90°F and in its original container.

Storage Conditions: Materials should be stored in a temperature and humidity-controlled environment and out of direct sunlight. The part B hardener is susceptible to freezing. Keep resins and hardeners separated from each other until ready for use. Materials should be kept away from sources of ignition.